• Sanjay Panwar

      Articles written in Bulletin of Materials Science

    • Aging of a copper bearing HSLA-100 steel

      Sanjay Panwar D B Goel O P Pandey K Satya Prasad

      More Details Abstract Fulltext PDF

      Investigations were carried out on aging of a HSLA-100 steel after varying amounts of cold deformation. Mechanical properties (hardness, tensile properties and toughness) were measured and structural changes were studied using optical, TEM and SEM techniques. As a result of various treatments, the hardness and UTS could be significantly improved, but with drastic fall in ductility and impact strength, especially in peak aged conditions. The parameters affecting impact strength were examined and it was concluded that various microstructural features affected toughness through their influence on tensile properties. In this steel the impact strength could be improved by lowering the UTS and increasing the ductility (pct elongation). The improvement in hardness and UTS was attributed to formation of thick precipitate-dislocation tangles. The aging process caused a slow transformation of lath martensite into acicular ferrite due to occurrence of in situ recrystallization. The concentration of Cu in particles precipitating on aging was followed using EDAX technique.

    • Effect of cold work and aging on mechanical properties of a copper bearing HSLA-100 steel

      Sanjay Panwar D B Goel O P Pandey

      More Details Abstract Fulltext PDF

      Influence of cold working and aging on the mechanical properties of a Cu-bearing HSLA-100 steel has been studied. The steel was given solution treatment at 1000°C, followed by cold rolling to 25, 50 and 80 pct deformations and aging at 600°C for various durations. Substantial improvement in hardness and UTS was observed in the peak aged condition of various treatments, but at the expense of ductility and impactenergy. Extensive scanning electron microscopic studies carried out on impact and tensile fracture surfaces suggest that poor impact energy and low ductility in peak aged condition could be associated with inhomogeneous deformation caused by the existence of coherent precipitates. Other parameters adversely affecting toughness and ductility in various stages of cold work and aging may include high stress concentration at high density dislocation network and dislocation–precipitate interface. Overaging in various treatments resulted in higher impact energy and ductility, presumably due to existence of incoherent precipitates and reduction in stress concentration at dislocation cell boundaries. It is observed that a good combination of high hardness and UTS with high impact energy and ductility could be obtained by a treatment suitable to cause coexistence of coherent and incoherent precipitates.

    • Effect of microalloying on aging of a Cu-bearing HSLA-100 (GPT) steel

      Sanjay Panwar D B Goel O P Pandey K Satya Prasad

      More Details Abstract Fulltext PDF

      Investigations were carried out on aging of a HSLA-100 steel containing Cu as the major alloying element and Nb, Ti and V as microalloying elements. The aging process after varying amounts of cold deformation was followed by hardness measurements and microstructural changes were studied using light and electron microscopy. Presence of Ti activates the formation of (Nb, Ti)C precipitates and completely suppresses the precipitation of Cu. Even a solution treatment at 1100° C is not sufficient to completely dissolve Nb and Ti in the matrix and undissolved (Nb, Ti)C precipitates were observed in oil quenched state. Strain induced aging at 400°C causes simultaneous coarsening of existing precipitates and nucleation of fresh carbides, which results in multi-stage hardening in this steel. Strong precipitate-dislocation interactions cause retardation in recrystallization of deformation structure leading to retention of high hardness levels even on prolonged aging.

    • Effect of cold work and aging on mechanical properties of a copper bearing microalloyed HSLA-100 (GPT) steel

      Sanjay Panwar D B Goel O P Pandey

      More Details Abstract Fulltext PDF

      Investigations have been carried out on the effect of cold work and subsequent aging on mechanical properties of a Cu-bearing HSLA-100 steel microalloyed with Nb and Ti. Aging at 400°C after various degrees of cold work (25–70 pct) exhibits multiple hardness peaks. The treatments cause significant improvement in hardness and tensile strength, but at the cost of impact strength. Cold work also causes deterioration in ductility, which again improves on subsequent aging. The C70A treatment involving 70 pct deformation exhibits maximum response to age hardening giving a hardness of 465 VHN and a UTS of 1344 MPa, but with low values of ductility (5 pct) and impact energy (24 J). C50A treatment involving 50 pct cold work and aging results in an optimum combination of mechanical properties. This treatment in the second hardness peak stage yields a hardness of 373 VHN, UTS of 1186 MPa together with a ductility value of 11 pct and impact energy of 109 J. Scanning electron microscopic studies of fracture surfaces reveal that the impact fracture occurs by formation of dimples and nucleation and growth of voids and cracks. Fracture in tensile specimens is caused by formation of voids and cracks at high density striations. Formation of voids and cracks is also assisted by the presence of precipitated carbide particles.

  • Bulletin of Materials Science | News

    • Editorial Note on Continuous Article Publication

      Posted on July 25, 2019

      Click here for Editorial Note on CAP Mode

© 2017-2019 Indian Academy of Sciences, Bengaluru.