Articles written in Bulletin of Materials Science
Volume 26 Issue 7 December 2003 pp 715-720 Glasses and Ceramics
Sodium aluminophosphate glasses having compositions of 𝑥Al2O3(1 – 𝑥)NaPO3 (𝑥 = 0.05–0.2) were prepared using conventional melt-quench technique. Density, glass transition temperature, microhardness (MH), thermal expansion coefficient (TEC) and transmission characteristics were measured as a function of alumina content for different samples. They were found to depend on O/P ratio with pronounced changes taking place for O/P ratio ≥ 3.5. Density, glass transition temperature and microhardness were found to increase up to 15 mol% of alumina and then they showed a decreasing trend. Thermal expansion coefficient decreased continuously with alumina content. Optical gaps for different glass samples as measured from transmission characteristics were found to be in the range 3.13–3.51 eV. It initially decreased with alumina content up to 15 mol% and then increased. The behaviour was explained on the basis of change in the average aluminum coordination number from six Al(6) to four Al(4) (i.e. Al(OP)6/Al(OP)4 ratio) along with the changes in polyhedra linkages in the glass network due to change in O/P ratio.
Volume 29 Issue 1 February 2006 pp 43-48 Ceramics and Glasses
Phosphate glasses having composition, 40Na2O–10BaO–𝑥B2O3–(50–𝑥)P2O5, where 𝑥 = 0–20 mol% were prepared using conventional melt quench technique. Density of these glasses was measured using Archimedes principle. Microhardness (MH) was measured by Vicker’s indentation technique. Structural studies were carried out using IR spectroscopy and 31P and 11B MAS NMR. Density was found to vary between 2.62 and 2.77 g/cc. MH was found to increase with the increase in boron content. 31P MAS NMR spectra showed the presence of middle 𝑄2 groups and end 𝑄1 and 𝑄0 groups with P–O–B linkages. FTIR studies showed the presence of BO3 and BO4 structural units along with the depolymerization of phosphate chains in conformity with 31P MAS NMR. 11B NMR spectra showed increase in BO4 structural units with increasing boron content. The increase in MH with B2O3 content is due to the increase of P–O–B linkages and BO4 structural units as observed from MAS NMR studies resulting in a more rigid borophosphate glass networks.
Volume 32 Issue 3 June 2009 pp 329-336
The degradation behaviour of phosphate glass with nominal composition, 40Na2O–10BaO–𝑥B2O3–(50–𝑥)P2O5, where 0 ≤ 𝑥 ≤ 20 mol%, was studied in water, HCl and NaOH solutions at room temperature to 60°C for different periods extending up to 300 h. These glasses were synthesized by conventional melt-quench technique. Dissolution rates were found to increase with B2O3 content in the glass. The dissolution rates for the glass having 10 mol% B2O3 were found to be 0.002 g/cm2 and 0.015 g/cm2 in distilled water and 5% NaOH solution, respectively, at room temperature after 225 h of total immersion period, whereas it increased considerably to 0.32 g/cm2 in 5% NaOH at 60°C after 225 h. However, glass samples with 𝑥 = 15 and 20 mol% B2O3 were dissolved in 5% HCl solution after 5 h immersion. The degradation behaviour has been correlated with the structural features present in the glass. The optical microscopy of the corroded surface revealed that the corrosion mechanism were different in acid and alkali media.
Volume 44, 2021
Continuous Article Publishing mode
Prof. Subi Jacob George — Jawaharlal Nehru Centre for Advanced Scientific Research, Jakkur, Bengaluru
Chemical Sciences 2020
Prof. Surajit Dhara — School of Physics, University of Hyderabad, Hyderabad
Physical Sciences 2020
Click here for Editorial Note on CAP Mode