G S Kumar
Articles written in Bulletin of Materials Science
Volume 17 Issue 4 August 1994 pp 405-409
Composites of BaTiO3 and CoFe2O4 have been prepared with various compositions by double sintering method. The presence of the two phases has been confirmed by XRD. Variation of dielectric constant with temperature in these samples has been studied. All the samples have shown linear magnetoelectric conversion in the presence of static magnetic field. The magnetoelectric effect (d
Volume 23 Issue 6 December 2000 pp 483-489 Oxide Ceramics
X-ray diffraction, a.c. impedance and conductivity (a.c. and d.c.) have been used to characterize DyBi5Fe2Ti3O18. Samples were prepared by solid state double sintering method. A few samples were also subjected to hot isostatic pressing (HIP) at 800°C for 2 h at 100 MPa pressure. The data on XRD, impedance and conductivity of two sets of samples are compared to understand study of effect of HIPing on the properties of DyBi5Fe2Ti3O18
Volume 24 Issue 5 October 2001 pp 487-495 Electrical Properties
The compound, LaBi5Fe2Ti3O18, is a five-layered material belonging to the family of bismuth layered structure ferroelectromagnetics. D.c. and a.c. conductivity measurements were performed on the samples. Dielectric measurements were also performed on these samples. Combined impedance and modulus plots were used as tools to analyse the sample behaviour as a function of frequency. Cole–Cole plots showed non-Debye relaxation.
Volume 24 Issue 5 October 2001 pp 497-504 Electrical Properties
The effect of lanthanum doping is studied on ferroelectric properties of Ba1–𝑥La𝑥TiO3 with 𝑥 = 0.0005, 0.001, 0.003 prepared through solid state sintering route. Dielectric and impedance spectroscopic studies have been carried out. The tetragonal distortion of the unit cell decreased and ferroelectric transition temperature, 𝑇c increased with the increase of lanthanum content.
Combined impedance and admittance spectroscopy was used to analyse impedance data. The electromechanical parameters were calculated from the resonant and anti-resonant frequencies from vector admittance plots. The electromechanical coefficients for Ba1–𝑥La𝑥TiO3 with 𝑥 = 0.003 were found to be much larger than that of pure barium titanate.
Volume 29 Issue 1 February 2006 pp 35-41 Ceramics and Glasses
Polycrystalline ceramic samples of sodium bismuth titanate with simultaneous doping at A and B sites have been studied for the influence of these dopants on the electrical conduction mechanism. A.C. conductivity measurements were done on the prepared sample in a wide range of frequency and temperature. These studies revealed that the conduction in the sample arises due to hopping of bound charges. Four-term power law is used to characterize the frequency dependence of a.c. conductivity. From the temperature dependence of the exponents, the a.c. conduction in the samples is explained.
Volume 29 Issue 4 August 2006 pp 347-355 Ceramics and Glasses
Electrical conduction studies on Ba(Nd0.2Ti0.6Nb0.2)O3 ceramic samples prepared through conventional and microwave sintering route are presented in this paper. D.C. and a.c. conductivities of these samples as a function of temperature from 300–900 K have been studied. Two types of conduction processes are evident from the frequency dependant conductivity plots, i.e. low-frequency conduction due to short-range hopping and high-frequency conduction due to the localized relaxation (reorientational) hopping mechanism. Grain and grain boundary contributions to the conductivity in these samples are obtained from impedance/admittance measurements via equivalent circuit modelling.
Volume 44, 2021
Continuous Article Publishing mode
Prof. Subi Jacob George — Jawaharlal Nehru Centre for Advanced Scientific Research, Jakkur, Bengaluru
Chemical Sciences 2020
Prof. Surajit Dhara — School of Physics, University of Hyderabad, Hyderabad
Physical Sciences 2020
Click here for Editorial Note on CAP Mode